About SBEW
Shree Balaji Engineering Works (SBEW) builds rolling mill machinery in Ghaziabad, India. We design every machine in-house, fabricate and machine it in our own works, and stay with the customer through erection, start-up and spares.
Whether you are setting up a new long-product mill, adding a melt shop or getting more tonnes out of an old line, we take the job from layout to first billet and first bar.
Meeting or exceeding customer expectations through continuous improvement.
Solutions
Turnkey melt shops that turn scrap and sponge iron into quality billets, ready for the rolling mill.
Long-product mills built around your product mix, size range and target tonnage.
Compact strip lines for producers who want to roll narrow strip for tubes and sections.
Turnkey tube mills and large diameter pipe mills, with the finishing equipment that follows them.
Upgrades for running rolling and tube mills – higher speed, better yield and less downtime.
Critical mill components made to drawing or designed by us for your duty.
Along the Whole Line
We supply one machine for one stage, or the complete line. This is where our equipment sits in a long-product steel plant.
Machines
A stiff, compact stand that holds tight tolerances and lets you change rolls quickly.
Horizontal and vertical rolls in one stand for beams and heavy sections with an even finish.
Compact stand for wire rod and small sections, with fast roll changes and strong shafts.
Takes the heavy lifting out of roll changes so the mill is back to rolling sooner.
Crops the head and tail of the bar on the run, for sizes from Ø 8 to 40 mm.
Cuts bars, billets and sections to length after cooling, with clean square ends.
Clutch and brake drive for heavy, repeatable cutting through a full shift.
Cuts red-hot bars and billets in line, fast and clean, with little heat distortion.
Carries bars from the finishing stand to the cooling bed at high speed, without overlaps.
Slows each bar after the shear so it lands straight – no twisting or surface marks.
Cools rolled bars evenly in air and walks them across on an automatic rake.
Moves finished bars from the cooling bed to bundling with less manual work.
Smooth, quiet power for critical mill drives, with gears designed on KISSsoft.
Reduction and pinion gearboxes built for the shock loads of a rolling line.
Melting & Heating
Melt shop, caster and furnace systems that feed your mill with steady, well-heated stock – and keep power and fuel use in check.
What Our Mills Make
Tell us the section and size range – we design the mill and the pass schedule around it.
How We Work
Your product mix, sizes, tonnage, space and budget.
Layout, pass design and 3D models of every machine.
Fabrication, machining and assembly in our own works.
Erection, trial rolling and hand-over at your site.
Spares, service and upgrades for the life of the mill.
Why SBEW
Design, manufacturing and service under one roof means one point of contact, shorter lead times and machines that fit together the first time.
3D models on SolidWorks and Solid Edge, gears on KISSsoft.
Fabrication and machining done in-house, not outsourced.
Our R&D house is recognised by the Government of India.
Melt shop to finished bar – one partner, one schedule.
Every part inspected from raw material to dispatch.
Spares and service to keep your mill running.
Research & Development
As a Government of India recognised R&D house, we keep refining our designs to raise mill speed and output and to lower the customer's cost per tonne.
Quality
Our management, engineers and shop-floor team keep improving our quality system, so every machine leaves our works accurate, reliable and on time.
Lifecycle Service
A mill earns only while it runs. We help you keep it running – and make it better over the years.
Ask for Spares →Gearboxes, rolls, blades and wear parts, made to drawing or to sample.
Our engineers set up the line at site and stay through trial rolling.
New stands, drives or a faster finishing end – added in steps, with short shutdowns.
Help with breakdowns, roll changes and getting more tonnes per shift.
Contact
Tell us your product, size range and capacity. Our engineers will get back to you with the next steps.
